Cruise Parts

250-3002 Rostra Closed Circuit Piggy Back cruise switch

The 250-3002 is a closed circuit cruise control switch that mounts directly to the vehicles existing turn signal lever shaft.  

250-2867 Rostra cruise switch with Speed Limiter + Memory

The 250-2867 cruise control switch is the control switch included in Rostra's "NS" kits. This switch cannot be used on non "NS" kits. It is for replacing a defective ONLY.  

250-2771 Universal Rostra Pedal Interface Harness

The 250-2771 is a Universal pedal interface harness for electronic throttle drive by wire vehicles. It can be used to replace a defective part out of the 250-1859 cruise control kit. Can also be used in conjunction with the 250-1882 universal electronic...

250-2761 Ford / Chrysler / Mopar Rostra Pedal Interface Harness

The 250-2761 is a Ford/Chrysler/Mopar pedal interface harness for electronic throttle drive by wire vehicles. It can be used to replace a defective part out of the 250-1847 and 250-1883. Can also be used in conjunction with the 250-1882 universal...

250-2766 GM Rostra Pedal Interface Harness

The 250-2766 is a GM pedal interface harness for electronic throttle drive by wire vehicles. It can be used to replace a defective part out of the 250-1848 or 250-9617 cruise control kit. Can also be used in conjunction with the 250-1882 universal...

250-2923 VSS Generator Magnet kit & Divider

The 250-2923 VSS magent kit is applicable to vehicles with an exposed drive shaft and an electronic throttle to produce speed signal for the new electronic cruise control kits. This part is included with the 250-1882 cruise control kit.   250-2923...

250-4160 Speed Signal Generator GM Style Speedometer Cable

The 250-4160 is a speed signal generator that goes in-line with a GM style speedometer cable, at the transmission. Simply unscrew the OEM cable from the transmission, thread the 250-4160 into the transmission, then thread the OEM cable on to the 250-4160...

250-2316 Rostra UltraCruise2 cruise control servo Replacement

The 250-2316 is the actual servo that comes in the 250-1223 kit. You can use this to replace an out of warranty servo for the following kits ;    250-1223 250-1799 250-1753 250-1766 250-1755   The 2316 does NOT come with a cable,...

Brushed aluminum Cover for 250-3020 / 3026 cruise switch

This is a brushed aluminum cover for the 250-3020 cruise switch. This part is also offered in a polished alumninum finish. Please choose the correct option for your interior trim.

Polished aluminum Cover for 250-3020 / 3026 cruise switch

This is polished aluminum cover for the 250-3020 cruise switch. This part is also offered in a brushed alumninum finish. Please choose the correct option for your interior trim.

250-3026 Gm style Cruise Switch 1978-1984 No Wiper Control

The 250-3026 is a GM style cruise control switch that is applicable to some 1978-1984 vehicles. If you have a lever that removes from the column by simply pulling it outwards, and has no wiper controls, this is the switch you need. Not compatible with...

250-2783 Rostra In-Line Diagnostic Harness for Can Cruise Kits

The 250-2783 is the Diagnostic harness for the new Can bus cruise control kits. Designed to go in-line with the OEM OBDII connector.

250-2785 Rostra Diagnostic Harness for Can Cruise Kits

The 250-2785 is the Diagnostic harness for most of the new Can bus cruise control kits. Designed to plug directly into the OEM OBDII connector.

250-3357 GM With Delay Wipers Cruise Control Switch

The 250-3357 cruise switch is designed to replace your original turn signal lever with delay wiper control only when using the Rostra Universal Cruise Control. Please call with any questions regarding application.  *** WILL  NOT REPLACE YOUR...

250-3020 Early Model GM Column Cruise Control Switch

The 250-3020 cruise control switch is applicable to early model GM columns. If the end of your rounded GM turn signal is flat, and is held in by a single set screw, then this may be the switch you need. Please call for application questions. This switch...

250-3032 "Cut Off" Universal Cruise Control Switch

The 250-3032 is a universal cruise control switch that mounts to the vehicles existing turn signal lever. You will have to sever the end of the original turn signal lever, and slide the 3032 over the original turn signal shaft. To be used in conjunction...

250-3096 Replacement Magnet Kit With Tie Strap

The 250-3096 comes with 2 replacement magnets as well as the original Tie strap. These are the same replacement parts that come in the 250-4165 VSS magnet kit. If you lost a magnet off of your drive shaft, these are the parts you need.

Toyota OEM Cruise Control Switch Knockout Prius 2006-2013

This is a gunuine Toyota cruise control switch knockout. It is compatable with the 2006-2013 Prius  ( NOT the Prius C ). This is a pre-cut knockout with a rubber dust cover. The exact same part that comes on the Prius with Cruise from the factory...

250-2214 Universal Parts Package

The 250-2214 is the universal parts package that normally comes in the 250-1223 universal electronic kit.

250-2317 Complete Harness / Wiring Assembly

The 250-2317 is the complete harness/wiring assembly for the 250-1223 Universal cruise control kit. 

250-3607 Replacement Cruise Control Cable

The 250-3607 is a replacement cable for the 250-1223 universal cruise control kit. Not applicable to any OEM cruise servos or any other aftermarket servos. ONLY the 250-1223

250-4165 Universal VSS Signal Generator Magnet kit With Pick Up Coil

The 250-4165 is a VSS magnet kit with pick up coil. Normal rear wheel drive domestic installation would take a single magnet on the drive shaft with a pickup coil mounted aprox 5/8 inch away.

250-4153 Speed Signal Generator GM Style Speedometer Cable

The 250-4153 is a speed signal generator that goes in-line with a GM style speedometer cable, at the transmission. Simply unscrew the OEM cable from the transmission, thread the 250-4153 into the transmission, then thread the OEM cable on to the 250-4153...

250-4379 VSS Signal Divider Interface

The 250-4379 is a VSS divider. Some vehicles have a speed signal output that is too fast for the 250-1223 kit to recognise. This adapter interface will divide the signal by 4.